Introduction to Lithium-ion Battery Installation on Small Craft

The aim of this course is to provide delegates with the underpinning knowledge of Lifting Operations in order for them to understand the role and responsibility of the Appointed Person in lifting operations (APLO). On successful completion of the course candidates will be able prepare and implement safe systems of work for lifting operations including writing risk assessments and method statements.

The aim of this course is to provide delegates with the underpinning knowledge of Lifting Operations in order for them to understand the role and responsibility of the Appointed Person in lifting operations (APLO). On successful completion of the course candidates will be able prepare and implement safe systems of work for lifting operations including writing risk assessments and method statements.

Almost a third of all workplace fatalities involve falls from high places – so safety training is essential for regulatory compliance and your own duty of care to anyone working at height. It’s most effective delivered in your real environment, with your own equipment.

The aim of the course is to provide delegates with practical and theoretical knowledge to safely work at height in the workplace. On successful completion of the course candidates will be able to select the correct height safety accessories, carry out pre-use checks and use equipment safely in the work place.

To provide Delegates with sufficient skills and knowledge to carry out their duties safely and efficiently whilst operating forklift trucks in the workplace.

CONDO training requires that personnel are adequately prepared for operational deployments, and that this training is dependent on a number of factors including the nature and location of the operation, the duration of task and the threat.  

The 1 day CONDO refresher training is required annually under DEFSTAN 05-129 (Defence Standards (Procedures & Requirements)) amended 12th March 2010.

The City and Guilds 6160-09 provides a medium risk entry / entry controller qualification at a nationally recognised level. Covering the fundamental principles of confined space working, any person with any exposure to confined space is recommended to attend this course. Although primarily aimed operatives it is a necessary foundation for all persons looking to progress their understanding of confined space entry.

This course was written by the Health and Safety Executive (HSE) to assist employers comply withe the HSE First Aid at Work Act (1981). It is the standard qualification for First Aiders in the UK work place and is nationally recognised. It is also the minimum First Aid qualification for anyone wanting to become either an HSE or RYA endorsed First Aid Instructor.

RYA Powerboat Level 2 (RYA PB2) offers a general introduction to power boating and teaches core boat handling and safety skills. The course is popular both with beginners and those who are self taught and now require formal certification.

If the worst ever happened at sea and you had to abandon your vessel, would you know what to do? The RYA Sea Survival training course assumes the worst case scenario: that you have to abandon your ship.

The RYA SRC (VHF Radio) course is the shortest of the four GMDSS Certificates and is aimed at skippers and crew of small craft operating in inshore and coastal regions. It is the most common radio certificate for leisure boaters.

This STCW First Aid course is designed for those professional yachtsmen, super yacht crew and seafarers who are required to comply with the STCW 95 code of practice and the STCW 2010 amendments. In the super yacht industry this certificate is required by all crew. In the smaller yacht and the workboat industry skippers operating up to 60 miles from a safe haven can operate with this certificate.

Teaches the actions to be taken by individuals to protect themselves in emergency situations. The first session is classroom based covering theoretical elements. The second session is practical training using life jackets, survival suits and inflatable life rafts in a realistic marine environment

This Instructor-led workshop provides safety awareness for all personnel who either use, handle or store liquid nitrogen.

The course covers the safe operation of a Gantry Crane along with Slinging and Signalling relevant to lifting with a Gantry Crane and references the Lifting Operations and Lifting Equipment Regulations 1998.

To provide Delegates with sufficient skills and knowledge to carry out their duties safely and efficiently whilst operating forklift trucks in the workplace.

This technical course will support delegates in understanding and describing the various mechanisms by which metals and alloys corrode and the technologies available for prevention.

This course provides an essential understanding of the symbolic language of GD&T within the context of the latest BS 8888 and ISO GPS standards. Delegates will learn how GD&T is used to convey design intent, guarantee both function and assembly, and, maximise tolerances.

Employers must provide training for operators of grinding machines and abrasive wheels, in compliance with their responsibilities under the Health & Safety at Work etc Act 1974 and the Provision and Use of Work Equipment 1998.

IOSH Leading Safely®️ equips business leaders and senior managers with the strategic health and safety knowledge necessary to safeguard their employees and business.

The IOSH Managing Safely®️ Refresher training course provides staff in managerial positions with a recap of the core elements of IOSH Managing Safely®. This includes areas such as how to identify, evaluate and control workplace risks, as well as how to evaluate safety systems and strategies in the workplace.

IOSH Working Safely® is an entry-level course which provides key health and safety training to employees across your organisation, enabling them to work safely and effectively. Developed by the Institution of Occupational Safety and Health (IOSH), the course teaches to the high standard of Health and Safety promoted by this globally chartered body, providing employees with practical, jargon-free knowledge and skills that they can apply effectively to the workplace.

The course is one day for civilians who work or provide a service to submarines. The course is called SMERAS - SUBMARINE, ESCAPE, RESCUE, ABANDONMENT & SURVIVAL and is held in the SMERAS Training Facility in Faslane, Scotland.

Spill Kit Awareness Training is an entry level course suitable for all staff who may be required to deploy spill kits following a spill incident in the workplace.

The City & Guilds accredited Authorised Person Electrical Low Voltage course will enable you to gain the knowledge required to carry out Authorised Person duties and responsibilities in order to achieve compliance with the requirements of the Electricity at Work Regulations 1989, using JSP375 as the reference for safe procedures.

This City & Guilds accredited course will enable you to gain the knowledge required to carry out the role of Skilled/Competent Person (Electrical). It can also assist in demonstrating competence during the formal appointment process.

This course will teach you about the welded joint, terminology, steps for successful design, and features of welding processes. You will also learn about edge preparations, weld symbols, residual stress and distortion, defects, weldability, and the strength of welded joints.

This 6 day course is a comprehensive introduction to chart work, navigation, meteorology and the basics of seamanship. You will find this course invaluable if you want to learn to start making decisions onboard in terms of safety, passage making, etc.         

A great 2 day course to introduce you to motor cruising and undertaking short in-shore trips, such as through a harbour or down river to the local beach. Time is focused on developing the core slow speed handling skills and good ‘seamanship’ skills.

Please register on any session showing, this will not be the date the course takes place. Upon registration your e-learning will then be booked and all of the log in details sent to you. You can undertake the training as soon as you have received this.

The Short Range Certificate is the minimum qualification required by law to control the operation of VHF and VHF Digital Selective Calling (DSC) equipment on any British flagged vessel voluntarily fitted with a radio. This includes both fixed and hand held equipment using international channels.

Originally designed for the Royal Fleet Auxillary, this course enables candidates to carry out lifting operations safely, and inspect lifting equipment for damage and wear to ensure safety for use. It includes legislation and documentation, followed by chain sling manufacture and repair, and practical inspection of chain, wire and textile slings, shackles and eye bolts.

This City & Guilds Accredited Programme is designed to provide delegates with a thorough understanding of Legionella bacteria, the risks it poses, and the necessary control measures to ensure compliance with health and safety regulations. Legionella bacteria, if not properly managed, can pose serious health risks, including the development of Legionnaires’ Disease, a severe form of pneumonia.

A 2 day, Qualpass accredited course. The course covers the safe operation of a Gantry Crane along with Slinging and Signalling relevant to lifting with a Gantry Crane and references the Lifting Operations and Lifting Equipment Regulations 1998. Delegates will complete a theory classroom session and assessment as well as a practical session and assessment covering Gantry Crane operation, slinging loads and moving loads.

The online Defence Single Source Training Workshop which will provide you with a framework within which your company can reach decisions about pricing and reporting relevant to their internal structure and methods.

A training course for practicing electricians who complete testing of electrical equipment/portable appliances, or who are involved in the management of such safety inspections. *Please note: All dates are subject to availability at the time of booking.

The Institute of Acoustics has the great pleasure to announce it is holding the International Conference on Underwater Acoustics.

This course will provide you with an appreciation of electrical engineering principles and the ability to interact effectively with colleagues regarding electrical issues. Within the course you will have the opportunity to analyse basic electrical components and their features and benefits. You will also gain an understanding of your responsibilities in the context of Electricity at Work regulations.

This Instructor-led workshop provides safety awareness for all personnel who either use, handle or store liquid nitrogen.

This CE & UKCA Marking training course provides a practical approach to what you need to know to place your products on the market and into service. The course covers the principles of CE & UKCA Marking for all fields.

COSHH awareness and CMS Training

IPC-J-STD-001 Requirements for Soldered Electrical and Electronic Assemblies. The sole industry consensus standard training covering electronic assemblies, Soldering, J-STD-001 is recognized globally for its criteria on soldering processes and materials. Updated with participants from 18 countries providing input and expertise, this theory and practical training brings the latest criteria along with new information to ease its use and comprehension.

This course will prepare you to take the INCOSE Knowledge Exam comfortably and covers all the information you need to know about applying for INCOSE’s Associate Systems Engineering Professional (ASEP) or Certificated Systems Engineering Professional (CSEP) certification.

This course offers excellent guidance on how to assess and plan the task of carrying out structural analysis using FEA.

A course based around the BMEEA Code of Practice, the industry recommended standard.The course is designed to give candidates a general overview of the knowledge and skills required for a BMEEA-certified Marine Electrical Technician. All information and required knowledge used mainly with UK marine electric systems and follows not only the BMEEA Code of Practice and ISOs, but also the Recreational Craft Regulations (RCR).

Please register on any session showing, this will not be the date the course takes place. Upon registration your e-learning will then be booked and all of the log in details sent to you. You can undertake the training as soon as you have received this.

Comprehensive VHDL is the industry standard training course teaching the application of VHDL for FPGA and ASIC design. Fully updated and restructured to reflect current best practice, engineers can attend either the individual modules, or the full course.

The CSWIP Visual Welding Inspector course is designed for welders, operators, line inspectors, and foremen who carry out the visual examination of welded joints. It is also suitable for welding quality control staff and anyone who needs basic training in welding inspection alongside a qualification.

This course provides a good understanding of DSP principles, and their implementation and equips you to put the ideas into practice and/or to tackle more advanced aspects of DSP.

This course has been introduced to raise awareness of environmental issues, with a primary focus within the Defence sector and the acquisition process. The course aims to assist delegates with the skills, knowledge and development potential to understand and manage environmental problems at the practical level. Delegates are also introduced to aspects of environmental legislation and the mandatory requirements for formal compliance in Defence

Consistently simple, structured and consistent project planning: Efficient and consistent project planning is based on a structured way of working. Use EPLAN Electric P8 to create electrical engineering documentation quickly, easily and safely. Get to know the basic working methods of the system on the basis of a practice-oriented and integrated project planning task.

Consistently simple, structured and consistent project planning: Efficient and consistent project planning is based on a structured way of working. Use EPLAN Electric P8 to create electrical engineering documentation quickly, easily and safely. Get to know the basic working methods of the system on the basis of a practice-oriented and integrated project planning task.

Expert VHDL is an intensive 5-day advanced application class. It teaches engineers how to increase productivity by enhancing their knowledge of the VHDL language itself and its application for design and verification. Presented in two distinct course modules, Expert VHDL focuses on language and synthesis issues, design maintainability and re-use, structured verification environments and the latest techniques for verification - including an introduction to OVL/PSL and introductions to OSVVM and UVVM.

This sonar course aims to provide you with a good understanding of the theory and practice of sonar technology, and its applications in the defence industry, environmental surveying and related fields; placing emphasis on the practicalities of sonar systems rather than on rigorous mathematical analysis.

Deep learning and machine learning techniques can be applied to a range of radar and wireless applications to meet the increased level of system requirements of operating in a crowded RF spectrum. For example, spectrum sensing, modulation identification, and signal classification are important functions for intelligent RF receivers. These functions have numerous applications in cognitive radar, software-defined radio, and efficient spectrum management.

This introduction to Sonar course aims to provide you with a good understanding of the theory and practice of sonar technology, and its applications in the defence industry, environmental surveying and related fields; placing emphasis on the practicalities of sonar systems rather than on rigorous mathematical analysis.

IEC 61508: Basic Functional Safety training includes course modules 1-3 and is designed to train participants in the basic principles of IEC 61508 Functional Safety, the processes necessary for your role in the safety life cycle (highly recommended for beginners) and also at the same time improve their expertise in safety related functions for Electrical, Electronic and Programming systems.

IPC 7711/21 is a procedures guide required to rework, modify and repair printed boards and electronic assemblies. This training programme teaches individuals industry approved techniques that are reliable, repeatable and safe. Reducing the cost of potentially scrapping or out sourcing assemblies.

IPC 7711/21 is a procedures guide required to rework, modify and repair printed boards and electronic assemblies. This training programme teaches individuals industry approved techniques that are reliable, repeatable and safe. Reducing the cost of potentially scrapping or out sourcing assemblies.

IPC/WHMA-A-620 training programme covers accept/reject criteria for cable and wire harnesses/assemblies showing acceptable and defect conditions aided by colour visuals and illustrations and also covers process requirements, making this a stand alone document. This industry developed training programme provides individuals with a credential that demonstrates their understanding of the document.

IPC/WHMA-A-620 training programme covers accept/reject criteria for cable and wire harnesses/assemblies showing acceptable and defect conditions aided by colour visuals and illustrations and also covers process requirements, making this a stand alone document. This industry developed training programme provides individuals with a credential that demonstrates their understanding of the document.

IPC-A-610 is the most widely used standard published by IPC covering industry-accepted end product acceptance criteria for consumer and high-reliability assemblies. This industry-developed training programme provides individuals with a credential that demonstrates their understanding of the document.

IPC-A-610 is the most widely used standard published by IPC covering industry-accepted end product acceptance criteria for consumer and high-reliability assemblies. This industry-developed training programme provides individuals with a credential that demonstrates their understanding of the document.

IPC J-STD 001, is recognised as the industry consensus standard covering soldering materials, processes and manufacturing of electronic assemblies. This industry-developed training programme includes a practical/ workmanship element that gives individuals all the tools to increase skills and performance.

Delegates will get a thorough insight into all aspects of life as a marine mammal observer. Ideal for those aspiring to a career in marine mammal observation, this course is also useful for anyone in industry working alongside an MMO who wants to get a better understanding of the role. The course starts in the classroom with a look at what exactly an MMO does, exploring: how noise impacts marine mammals; the legislative landscape; record-keeping; reporting requirements; and mitigation measures.

In the LabVIEW Core 1 Course, you will explore the LabVIEW environment and interactive analysis, dataflow programming, and common development techniques in a hands-on format.

The LabVIEW Core 2 Course will teach you how to prepare, debug, and deploy stand-alone applications. The course covers topics including use of event-driven programming and programmatic control of your user interface. This course provides the second step in the LabVIEW learning path as an extension of the LabVIEW Core 1 Course.

This course demonstrates how the timely and tailored application of these issues identifies and manages risk, lowering the acquisition and whole life cost of a project resulting in cost-effective and successful programmes. Examples of the implementation of these essential principles across design, upgrade and off the shelf programmes for both hardware and software together with the varying terminology used within the discipline are considered.

A Marine Electronics qualification, which encourages a high level of professional expertise in entry-level and mid-level technicians and to lead them to further develop their skills

Ocean Microstructure Glider Workshop

The Health and Safety in Ship Operations Course is a comprehensive look at health and safety, in all its guises and how it operates in the maritime sphere. This course provides a full understanding of all aspects of health and safety in terms of its applications to ships, rigs, ports/mariners, and workers. With the aim of maintaining a broad approach to help students build a reliable knowledge base, this course covers a large spread of topics.

This Fire Marshal training course covers the role of the designated fire marshal (fire warden). You will learn about preventing fires, and about the different types of fire extinguisher and how to use them correctly.

The 3 day First Aid at Work course is our most advanced First Aid course. It provides you with a comprehensive set of skills needed by any first aider at work. 3 days of practical, fun and interactive First Aid training. Gain the skills and qualification needed to be a First Aider on site. After successfully completing the course, you are provided with a certificate which is valid for 3 years. This complies with the Health and safety at work act 1974.

The 2 day First Aid requalification course is a condensed version of the 3 day First Aid at Work course whereby we cover all topics in 2 days rather than 3. Only students who hold a current 3 day First Aid at Work certificate or a certificate that hasn’t expired by more than 28 days can attend.

This three-hour practical refresher course provides first aiders with an opportunity to practise and update their skills as a qualified first aider, at any time while their first aid certificate is valid.

The FAW, First Aid at Work Course syllabus as written by the Health and Safety Executive (HSE) to assist employers to comply withe the HSE First Aid at Work Act (1981). It is the standard qualification for First Aiders in the UK work place and is nationally recognised. It is also the minimum First Aid qualification for anyone wanting to become either an RYA endorsed First Aid Instructor.

Ideal for those who work in an environment with lasers, but who have no need of in-depth technical knowledge.

The objective of this short training course is to raise awareness to the dangers and consequences of pressure injection injuries. To build a greater understanding of how to prevent such injuries through improved working practices.

RYA First Aid gives you some knowledge so that in a medical emergency, you may be able to save lives, especially when you are in a remote location or at sea. This course is unique, as it is aimed at water sports enthusiasts and small craft operators, it takes a realistic look at the levels of First Aid that can be performed in a yacht, powerboat, dinghy or ocean rowing boat.

This is an advanced course in navigation and meteorology for candidates for the Coastal Skipper and RYA Yachtmaster Offshore Shorebased Certificate

The internationally-respected PAM Level 1 course combines classroom study with practical experience at sea to equip delegates with the all the skills required to become a professionally qualified Passive Acoustic Monitoring (PAM) Operator.

The OPUS10 Basic Course is an introduction to spare parts management and teaches basic skills in using OPUS10 for spare parts optimization. The objective of the OPUS10 Basic Course is to enable participants to understand basic logistics modeling and to familiarize them with the main OPUS10 functionality.

This course will provide leadership skills development in the application of quality planning within the context of product/service portfolio management. Delegates will leave the course with the capability of coaching and facilitating top management teams in the development of their understanding and deployment of the strategic management of portfolios of products/services, quality policies and the roles required.

FEA is a powerful technique, able to produce solutions to challenging structural analysis problems. The technology and computational efficiency of the method, together with the rapid increases in computer processing power means that today the scope and size of simulations far exceeds the capabilities of even a few years ago.

This flexible online course will give you the knowledge and skills you need to effectively manage engineering teams, projects, departments and companies. You’ll develop a keen awareness of employer and customer needs. You’ll also gain an understanding of the changes in business, industry and government that affect engineering management.

This programme will provide delegates with an understanding of health and safety requirements relating to their work activities. It will highlight organisational and human influences on safety at work and focus on a range of risk control measures essential to company activities. It will help to develop an approach to safe working, using the principles outlined in Successful Health and Safety Management HSG65 together with the more fundamental tried and tested techniques of health and safety management.

The RYA Day Skipper Motor (Power) Course includes boat handling safety and navigation skills and is aimed at new motor cruiser skippers. It enables new motorboats to skipper a motor cruiser in familiar waters by day. Any UK citizen or bona fide resident who achieves the Day Skipper Power is automatically eligible for the ICC (International Licence) for powered craft (unrestricted by length).

The RYA Day Skipper Shorebased theory course will help you become involved with onboard navigation and passage planning or become a skipper. This course is aimed at; Those new to boating (yachting, keel-boating, motor boating, power-boating or coastal rowing) and Those who already have considerable crewing experience and now want to progress

Master the key elements of contemporary electronic and electrical engineering with this accredited MSc Electronic and Electrical Engineering course. You'll design and implement electronic systems, work with the practical application of current technology, and upgrade your skills to meet the needs of more ambitious roles in your industry.

Please register on any session showing, this will not be the date the course takes place. Upon registration your e-learning will then be booked and all of the log in details sent to you. You can undertake the training as soon as you have received this.

This course is designed to increase and improve the knowledge of Maintenance Staff and Managers at all levels. This extended knowledge will enable staff to better maintain and manage Fluid Power Systems with a better understanding of component function and operation They will follow safer working procedures and once they have completed the practical training, their work-based skills and role competency will improve. Staff will also work together with greater synergy and levels of communication.

Globally accepted Functional Safety Engineer certificate with lifetime validity for engineer level. Improve your knowledge of functional safety with our three-day online instructor-led course, accredited by TÜV SÜD and focusing on the ISO 13849 & IEC 62061 standards. This course is ideal for UK professionals involved in managing or designing safety-related control systems in machinery.

Safe casualty assessment and handling.

During the training they will be taught the appropriate skills to produce Stepped Shaft Mill Block Drill Drift

This 3 hour training course has been designed to introduce delegates to the basic concepts of working with hose and connectors. Correct safe working practices will be discussed along with the associated dangers of fluid/pressure injection injuries.

Please register on any session showing, this will not be the date the course takes place. Upon registration your e-learning will then be booked and all of the log in details sent to you. You can undertake the training as soon as you have received this..

This course covers the requirements of the Provision and Use of Work Equipment Regulations (PUWER) and provides delegates with a thorough knowledge of this legislation and the duties of an employer to provide safe equipment for their employees to use. The course explains the implications of modifying machines and the steps that need to be taken to evaluate new machines.

Rack safety inspections are required to prevent and minimise the effects of accidents, to comply with the requirements of PUWER 1998 and to promote safety in the workplace

Electricity can kill or severely injure people and cause damage to property. Learning to work safely with or near electricity and electrical equipment can significantly reduce the risk of injury to workers. This training course provides relevant legislation, guidance, and industry best practice​ in relation to electrical safety and gives delegates a practical understanding of what HSE inspectors are looking for in the control of electrical safety risks, including the effectiveness of appropriate controls

The aim of this course is to give delegates a level of competence which will enable them to train others in the safe operation of the Evac+Chair.

This one-day course will help you meet your regulatory requirements if your risk assessment indicates that first aid training covering emergency protocols only is sufficient for your workplace.

FloEFD is a fully CAD embedded Computational Fluid Dynamics (CFD) software solution that is used for the analysis of heat transfer and fluid flow design challenges. Working with Solid Edge native geometry, it allows designs to be analysed quickly and accurately to determine product performance. The FloEFD essentials course will get you quickly up to speed, making best use of the simulation tool.

The course is suitable for any employee appointed as a Fire Marshal or Fire Warden. The course is also suitable for those employees looking to enhance their overall fire safety knowledge.

Solid Edge Simulation is a built-in finite element analysis (FEA), pre- and post-processing, tool for design engineers. This course will teach you how to digitally validate part and assembly designs within Solid Edge, analyse different mechanical load cases and boundary conditions and accurately interpret the results.

Please register on any session showing, this will not be the date the course takes place. Upon registration your e-learning will then be booked and all of the log in details sent to you. You can undertake the training as soon as you have received this.

Legionella Responsible Person Training Course provides a detailed insight into legionella management. This includes evaluating water treatment options for hot and cold water systems.

This course is designed to teach soldering skills and the requirements of high reliability soldering, with emphasis on the IPC standard for soldering. This course is designed for an introductory level for those new to hand soldering or wish to refresh or enhance previously gained skills.

This course gives you, the design engineer, the means to identify and prioritise the critical tolerances that govern the fit, form and function, while striking an effective balance between the use of cost and time.

The Yachtmaster Power (Coastal and Offshore) Certificates of Competence Courses are run together. Whilst the syllabus for each is very similar, the Offshore candidate requires more logged sea time and will be pushed harder in the exam. If you’re unsure as to exactly which level you should aim for, we are happy for you to book the preparation course and decide part way through, once you have seen the kind of exercises involved. PLEASE NOTE THE PREREQUISITES FOR THIS COURSE

This City & Guilds Assured training course will enable you to gain the knowledge required to carry out the role of Competent Person (Electrical). It can also assist in demonstrating competence during the formal appointment process. The course meets the criteria contained in Appendix 7 of HTM 06-02.

MAXURF MODELER Training focuses on good modelling practices with downstream 3D CAD in mind. Best practices. Examples include both monohull- and catamaran boats. MAXSURF STABILITY Hydrostatic- and stability training includes setting up load case-, tank- and compartment definitions to be used in the calculations. Intact- and damage case evaluations are studied. MAXSURF RESISTANCE AND MAXURF MOTIONS INTRO Resistance/power training covers calculations for different types of vessels.

The internationally recognised IPAF scissor lift course and cherry picker training course is in place to provide delegates with a range of MEWP training, from cherry picker training to scissor lift training. The course covers accident prevention, safe operational procedures, and emergency descent operations and gives an overview of the responsibilities of employers and employees.

IPC J-STD-001 - IPC Specialist Refresher

From an introduction into Solid Edge Motion to using motion entities, after this 1-day course, you will use the Solid Edge Motion functionality confidently.

Solid Edge Advanced PMI/Detailing

Attending the AQAP 2110 & AQAP 2310 – Understanding & Implementing Training will strengthen ATLAS capability to meet NATO aligned quality requirements and deliver products that consistently meet defence sector expectations.

The Solid Edge Advanced User course builds upon the Essentials training course. After assessing current ability, we introduce more advanced topics and modelling techniques. We continually reiterate best practice and an optimum approach to the fundamentals of 3D CAD. Advanced techniques and tips will help users create better and more robust 3D models. We will also introduce you to the inbuilt tools to automate part creation.